Loopla!

Elastic is very hard to come by these days. In the beginning of "hunker down" I made a few masks for my husband using ponytail holders for the ear loops. They are hard to sew because they roll, and I only have enough for about 7 or 8 masks. (I don't know how hard it would be to get more.)

One of my early masks, using ponytail holders

I tried out one of these masks and I found the ponytail holders to be very uncomfortable for more than 5 seconds. Perhaps it was one of my earlier masks. They were quite narrow - between 5" and 6" wide. I am making them 7" to 9" wide now. That would have made a difference in how tight the loops felt.

But working with the Lycra-type fabric gave me an idea. It is so stretchy. I wondered if I could use it in place of elastic. It would be more comfortable than ponytail holders, and easier to sew.

My finished product is this mask, which I have named "Aurora." I had a few false starts and ended up ripping out every seam at least once. But ultimately, it was a success!

Aurora

I wasn't sure how long to make the loops. It seems that there would not be one standard measure because different loop materials have different levels of elasticity. It also depends on the width of the mask and on the wearer's face. 

I started out with 6" x 1" strips of Lycra (unstretched). I made up a prototype mask, basting the seams, and it was tried on, and slight adjustments were made. I ended up with 5 ¾" x 1" strips of Lycra.

Sample zigzag stitches on folded Lycra strip

I also wasn't sure whether to fold the Lycra in half and sew it, or fold it in half where it is sewn into the seam without sewing it, or not fold it at all. I ended up folding and sewing it. It seemed to need the stability. I used a stitch called multiple zigzag stitch or tricot stitch. It was hard to sew a straight line in this stitch on a 1" strip folded in half, but it was good enough for my purpose. The multiple zigzag stitch did not seem to limit the ability of the loop to be stretched. By contrast, a regular zigzag stitch worked poorly. It inhibited the stretching and it caused the piece to curl up.

Close-up of finished loop

The filter pocket on the other side of the Aurora mask

I made a filter pocket for the Aurora mask using a method I had seen on the internet. The method requires two full size pieces of lining that you sew together in the center, leaving a gap in the middle. You then fold the ends of each piece together and you have a pocket with finished edges.

I do not recommend this method for two reasons. First, it is difficult to insert a filter. (Maybe I should have made the gap wider.) Second, when the mask is worn without a filter, speaking seems to open up the gap, resulting in only a single layer of fabric near the mouth. This would be worse with a wider space for inserting a filter.

To recap:

• Lycra loops are a good substitute if you don't have elastic but you do have Lycra.
• They are very comfortable.
• You may have to adjust the length for different masks or different wearers. (Maybe you have to do that with elastic loops, too?)
• They are easier to work with than ponytail holders, especially if you elect to skip the zigzags.

It's the Berries!

I was excited to get some Lycra-type fabric from Leah, because that is what the mask pattern I want to try next calls for. "Lycra" is a trademarked name, and I don't know if the fabric I got is actually Lycra, but I don't have another name for it. It is extremely stretchy.

The mask pattern I want to try comes from a company called EldenberryBlossoms. That's "Eldenberry" with an "n", no space, "Blossoms." This pattern is almost impossible to find using Google, so I will just tell you to go to the Facebook page for "EldenberryBlossoms Pattern Group," and ask to join the group. When you have been approved you will be given access to "Files" and you will be able to find the mask pattern there. I will call it the EB mask from here on.

The EB mask is similar to the fitted mask, but it uses something stretchy along the top and bottom edges. I was hoping this would help it to fit the face more snugly. Specifically, I am trying to address the problem of glasses fogging up.

I had previously made one Eldenberry mask using t-shirt strips. It turned out ok. I thought it might turn out better with Lycra.

Inevitably, you will find some aspect of the pattern that you want to change. For me, it was the ties. The pattern said the ties should be16-24". I thought that was a little short, since I make the ties 16" long on each side when I make other styles of mask.

In theory, the EB mask is an easy mask to make. You cut two outsides and two insides and two long 1½" Lycra strips. You sew the center seam on the inside and the outside. You machine hem the four side edges. You sew the tops and one  Lycra strip together with a single seam, then repeat for the bottoms. Turn it right-side out and you are done. No top-stitching. Practically no ironing.

So why does it take a couple of hours to make one? 

• Part of it is my perfectionism. 
• Most of it is that it's hard to sew the long seams with the Lycra pieces. You have to stretch the Lycra while you are pinning/sewing. As soon as you let go, both the sewn and unsewn parts want to spring back and bunch up. The fabric wants to slip, and you end up with a seam allowance on the underside that might be too narrow. The stretching is uneven. 
• Lycra is hard to cut into long strips. 
• You might forget to hem the sides. 
• It's harder than you'd expect to remove stitches from the Lycra and the stretched fabric. 

And so on. It was berry frustrating.

Ta dah!

With the EB mask pattern there is a slight difference between the top and the bottom of the mask. It is hard to see on a finished mask (or on an unfinished mask), but it makes a difference in how the mask fits. One way to deal with this is to use fabric with a directional print.

I do worry a little about the aqua mask. The blue Lycra was much stretchier than the black Lycra, and I may in fact have stretched it too much. I will have to wait for feedback from Spokane (where these two masks are headed). 

I made the rust-colored mask first, and I measured the Lycra without stretching it. My 24" ties seemed a little on the short side, so when I made the aqua mask I sewed two strips together to make longer ties. I used a stretch needle and a zigzag stitch to do this. As it turned out, the blue Lycra was so much stretchier than the black that it probably wasn't necessary to sew two strips together. But I didn't realize that until later. 

So, I had a big lump where the two pieces of Lycra were sewn together. I decided to stretch the tie out so that the lump was not part of the seam. Instead, the lump was next to the fabric.

This is not a mask a perfectionist would make.

If I do this again, I will try joining the ties with a diagonal seam.

I noticed a lot of tiny threads or beads of Lycra while I was working with it. I hope the ties won't continue to unravel over time.

On the plus side, I think these masks will fit their intended recipients well. The pattern comes in four adult sizes and three youth sizes. 

The EB Mask gives you an automatic filter pocket. There is a template for filters in the Facebook "File" mentioned above.

I am going to withhold judgment on this mask until I get feedback from Spokane.

And just for fun, here are the two fitted masks that went out to Spokane in the same package.

Jersey Girls

It's been quite a while since I posted. I've been busy making masks. I have actually had a lot to post about, but never seemed to have time. I do realize that "having time" is a choice, but that's a topic for another day.

So, let's get started.

Leah generously shared her amazing collection of jersey with several of us in the mask-making group. Wikipedia defines jersey as follows:

• Jersey is a knit fabric used predominantly for clothing manufacture. It was originally made of wool, but is now made of wool, cotton, and synthetic fibers.

I have no quibble with this definition. It covers a lot of ground, or perhaps I should say yardage.

And Susan generously shared some elegant fabric from her stash. I am eager to get to work.

I received two types of jersey. One type is a soft, lightweight ribbed knit. The ribs are very fine, about 20 to an inch. The other type of jersey is a strong, stretchy lycra-type fabric.

I have been using old t-shirts, and I am starting to run out, so I am excited to be able to augment my supply, and maybe get some colors I don't have.

What I do with t-shirts is this:

1. Cut a 1-inch strip.
2. Pull hard on the strip to stretch it. It will roll up and stretch out, but it will spring back part way.
3. Measure and cut. Voila! Mask ties. So easy.

Here's what happened with the ribbed jersey. First, I had to decide which direction to cut. It seemed to stretch when I pulled perpendicularly to the ribs. It did not stretch at all when I pulled in the direction of the ribs. So I cut across the ribs.

After I pulled to stretch out the strips, I got this:

It became narrower, very thin, and no longer stretchy. It did not snap back. It doesn't seem sturdy enough to use for masks.

Next, I tried cutting in the direction of the ribs. I got straps which are acceptable, though not elastic in the least. (I couldn't decide whether to take photos in the sun or shade, so the colors are looking different. Apologies.)

I finished two masks using the parallel-to-the rib ties. I like these ties. They make the mask lighter, and the bulk is reduced at the point where the ties are sewn into the seam. And such gorgeous fabric!

I am happy with the way these turned out. However, I don't think this ribbed jersey will be suitable for the Eldenberry-style masks I am planning to make. Comments?

I would appreciate any suggestions from others on sewing with jersey, especially since I haven't tried the lycra yet. And I haven't washed these masks yet, though I plan to do so today.

Mask up!