On Ringo Lake, Part Five - Keeping My Feet Wet

I managed to do hardly any quilting this weekend. Just enough to keep my feet wet. It was another week for flying geese in the Bonnie Hunter mystery quilt. Lots and lots of them. (Here's a link to On Ringo Lake, Week Five.) 

I just started cutting without really thinking. Just mindlessly following the directions as to cutting size. Forgetting that the Simple Folded Corners Ruler had alternate directions. Forgetting that "folded corners = flying geese". Not remembering until I had made a bunch of unacceptable flying geese.

I had used the SFC Oversized Method for week three, which wasn't exactly flying geese, so it took a while for the little light bulb to go on. You have to think about using the Oversized Method BEFORE you start cutting.

So here are some pieces that turned out okay:

"Honk, Honk!" they said

I am sure I will be able to make quite a few more before Friday. 

These large squares will be cut diagonally to make large triangles for the oversized Method.

Is it just my imagination, or does this year's mystery quilt have a lot more pieces than previous Bonnie Hunter mysteries? 

The rest of the story, since Vireya asked:

This is where it was stashed. Bad idea!

It just doesn't want to lie flat any more.

I tried ironing the mat on the lowest setting (before the photo above was taken). It helped somewhat. I need to keep working on it. The worst that can happen is I can ruin the mat, right? 😉 

Lessons Learned:

• Before cutting all the fabric, make a few samples. Or, review all prior instructions carefully. 

On Ringo Lake, Part Four - Treading Water

I'm treading water. I'm working hard, but I'm staying on top of this project. Here is a link to this week's clue: On Ringo Lake, Week Four

This week we made triangles. 
I will need an awful lot of them, and I have only made about one-third because this is a very busy week. They do go much faster than last week's pieces, and I'll take that.

I used the Essential Triangle Tool to make the brown wing triangles. I like this method because it minimizes waste. I also like the way you end up with notched corners on one side.

My "Problem of the Week" is the failure of the wing triangles to align sometimes:

Yes, I pinned, but I still have about a 20% reject rate. (Pout.) I tried flipping the pieces over and sewing with the aqua square on top. That helped somewhat, especially when sewing over that seam while adding the second wing triangle, but I am still getting rejects. It's really frustrating because I have been cutting and sewing so carefully.

Last week I mentioned that the Oversized Method didn't waste much fabric. Here's the proof:

On the left: waste from the No-Trim Method - On the right: waste from the Oversized Method

I continued making Week Three pieces after I published my last blog. I really liked using the Oversized Method and found that I could use that method without pinning. How great is that?

I have also been thinking about two particular neutral fabrics I have been using. I really don't like them. They have a very low thread count, and I just don't like the way they look.

Not happy with the way these fabrics look

I got them at a "good" quilt shop. I KNOW that fabric from places like Jo-Ann's usually has a low thread count. I didn't expect it from the more expensive fabric sold at a good quilt shop. I was mainly paying attention to color and pattern at the time, not to fabric quality. I bought a fat quarter of each. I don't think I'm going to use them any more.

Lessons Learned:

• Always pay attention to thread count and fabric quality, no matter where you are purchasing it, and no matter how great the fabric color/print is.
• Don't lean your cutting mat against a wall where there is a baseboard heater.

On Ringo Lake, Part Three - In Over My Head

I did not quite finish the many pieces mandated for Week Two. I spent way too much time ripping out and re-doing. I had to re-sew 40 to 50% of my pieces because 1) I am a perfectionist, and 2) the pieces were slipping too much when I sewed them.  I tried pinning. It didn't help much. I tried using more pins. That only helped marginally.  I tried pinning more "strategically." I tried adjusting the presser foot. I tried sewing faster and sewing slower.  I don't know why this was so hard for me. The pieces were fairly small, and I think that magnified any discrepancies. Whatever the problem, it was very frustrating.

I told myself I would try another method when I finished using all the pieces I had already cut. I know I didn't have to do that. I could have just stopped using the already-cut pieces. I could have started to cut new pieces using a different method before I had used up all the old pieces. But I did not want to throw out perfectly usable pieces, so I just kept on keeping on.

When I finished up the pieces I had cut in advance, I switched to the Oversized Method. This method is described in the instructions that come with the Simple Folded Corners Ruler.  

This is what the Oversized Method yields, before trimming. I have drawn a blue box to show the trim lines. Notice how forgiving this method is.

Up to this point I had resisted the this method because I thought there would be a lot of wasted fabric. Once I started using the Oversized Method, and I began to understand it, it became clear that this method didn't waste any more fabric than the No Trim/Exact Size Method, which is the other method described in the instructions for the SFC Ruler. (If you really care about not wasting fabric, Bonnie Hunter also describes a no-waste method, using the Essential Triangle Tool, in the instructions for Week Two.)

I think I have found something that really works for me! Not only does the Oversizde Method seem to minimize ripping out seams and re-doing, I am finding that I can use it successfully WITHOUT ANY PINNING. And, as a bonus, it is not necessary to cut the corner pieces with extreme precision because you will be trimming them later. (You should still be fairly careful, but you don't have to be extraordinarily careful.) So I am getting my pieces done much faster.

That's a really good thing because Week Three's pieces also have folded corners, and there are even more pieces this week than last week. Here is your link to Week Three: On Ringo Lake, Part Three

Some of my finished pieces. How will they fit together?

I am also working very carefully with these pieces because I want to make sure I pay attention to the directionality. I am making twelve at a time so I can keep track of things.

Despite the method breakthrough I am still way behind on my Week Three pieces because I spent a lot of time on Friday visiting fabric shops. I needed more melon and neutral fabrics. I did well. I got more of one of the neutral fabrics I had bought as an experiment, and I got several new fabrics which either recently arrived or which I had previously overlooked. Whatever, I am happy! Pretty new fabrics!

I love this one so much I don't know if I can bring myself to cut it

Lessons Learned:

• There may be more than one method to cut and sew a particular piece such as the Flying Geese
• If one method isn't working well, or is a lot of work, keep trying other methods. I tried a total of four methods for Flying Geese.
•  When you have a lot of interruptions, it is helpful to break complicated work down into bite-size pieces.